The Stokke® Table Top suction cups are packed in pairs and these are stuck together in the packaging. Please check whether you have two packages of two suction cups. If this is not the case, please contact our Customer Service helpdesk for your respective country via the following link and provide your full address details: http://www.stokke.com/global/contact-us Read More

Due to the light weight of the Stokke® Home™ Cradle, our Stokke® designers developed the cradle without wheels. This is also beneficial with regards to the safety of the infant. Read More

Read More

To keep your Stokke® Home™ Dresser clean, wipe it with a soft, damp (not wet!) cloth. Wipe down with a dry cloth until completely dry. Refrain from using a micro fibre cloth or household detergents as they may damage the finish of the crib. Colours may change if the products are exposed to sunlight. Read More

"The dimensions and weight of the Stokke® Home™ Dresser when packaged in the box are: Box 1 of 2 (weight 24kg (53 lbs) / L: 67cm (26,3’’) / W: 8cm (3,1’’) / H: 78cm (30,7’’)) Box 2 of 2 (weight 24kg (53 lbs)/ L: 57cm (22,4’’)/ W: 8cm (3,1’’) / H: 74cm (29,1’’)) When assembled, the measurements are as follows: L: 73 (28.5"") / W: 50cm (19.5"") / H: 88cm (34.5"") Weight: 40 kg /88 lbs (2 Boxes) " Read More

Read More

"The Stokke® Home™ mattress cover can be hand-washed at 40 °C. Make sure to stretch it to size whilst still wet. Do NOT use a tumble dryer. The foam filling can be hand washed at 60 °C and/or rinsed with warm water. We recommend the use of protection sheets in case of little spills or accidents. " Read More

Read More

• Always make sure the bumper is fixed correctly and tightly to avoid sagging. Check frequently that all the bumper ties are firmly tied to the crib rails. Please re-tie if necessary. • To ensure optimum airflow, always ensure the child is not sleeping with their face in direct contact with the bumper. • Remove the bumper when the child can sit unaided or pull themselves up to a standing position. Read More

The standards the Stokke® Bumpers comply with are: • ASTM F1917-12 – “Infant Bedding and Related Accessories” • BS 1877-10:2011+A1:2012 – “Domestic bedding. Specification for mattresses and bumpers for children’s cots, perambulators and similar domestic articles” • The above standards specifically aim to ensure safe design and sufficient care instructions for safe and proper use of a bumper. • Stokke® Bumpers have been tested for CO2 retention and results show no increase of CO2 in the crib environment with a correctly fitted Stokke® Bumper. • Stokke® Bumpers are designed with specific dimensions and materials to ensure optimum air flow. Read More

All textiles can be ironed, except Stokke® Home™ Bed Protection Sheet. You will find this information on the care label attached on each product. Read More

Yes, Stokke® Home™ Half Bumper fits on both Stokke® Sleepi™ and the Stokke® Home™. Read More

Read More

Stokke® iZi Go Modular™ by Besafe® has an integrated adapter so you do not need any additional adaptors or parts to use it in conjunction with a Stokke® Crusi, Scoot and Trailz. Please note that the Stokke® iZi Go Modular™ by Besafe® can be attached to Xplory starting with serial number 24770 and above. Read More

Stokke® iZi Go Modular™ by Besafe® can be used up to when the child is 75 cm (approximately 12 months). Read More

We suggest to keep both pillows for the first 4 months. When the child is between 4-6 months the pillow placed under the insert can be removed. When the child is 6 months the pillow which is part of the baby insert can be removed as well. Read More